Fröling T4e Operating Instructions Manual Download Page 52

Page: 52 / 76

WARNING

Incorrect inspection and cleaning:
Incorrect or insufficient inspection and cleaning of the boiler can cause serious

faults in combustion (e.g. spontaneous combustion of carbonisation gases / flash

fires) and this can lead to serious accidents and damage!

Take the following precautions:

❒ Clean the boiler following the instructions in the instruction manual. Follow the

boiler operating instructions.

5.2 Required tools

The following tools are required for carrying out cleaning and maintenance work:

Included in delivery:

Furnace tool with bracket

Spanner for door mountings

Socket wrench AF 13

53x53x110 cleaning brush to clean the WOS springs

Not included:

Spanner or box wrench AF 13

Screwdriver set (Philips, flat head, Torx T20, T25, T30)

Small brush or cleaning brush

Ash vacuum

Servicing the system

Required tools

Froling GesmbH | A-4710 Grieskirchen, Industriestraße 12 | www.froeling.com

Summary of Contents for T4e













































































Search results

Summary of Contents for T4e

Reviews:

Related manuals for T4e

Brands by name

Popular brands

Fröling T4e, Operating Instructions Manual

Search results

Summary of Contents for T4e

Reviews:

Related manuals for T4e

Brands by name

Popular brands