Friulinox Cube Series Service Manual Download

Page: 72 / 89

“go to

TABLE OF CONTENTS

”

FRIULINOX ALI GROUPS.R.L. A SOCIO UNICO

Via Treviso,4 - 33083 Taiedo di Chions (PN) -Italy

Servi

9.2.

Malfunctions not managed by board

9.2.1.

The display board does not switch on

see
par.

8.1

1. Check that there is power on the power socket where the equipment is connected

2. Access the electronic board and use the multimetre to check for power supply (230V)

at the board input (“faston” terminals L and N)



see wiring diagram

If there is power supply and the board does not turn on, check for power supply (12VDC) at the T1 transformer output

If there is voltage (12VDC) and the board remains off



replace the electronic board

If there is no voltage at “T1” transformer output (12VDC)



replace the transformer

Summary of Contents for Cube Series


























































































Search results

Summary of Contents for Cube Series

Reviews:

Related manuals for Cube Series

Brands by name

Popular brands

Friulinox Cube Series, Service Manual

Search results

Summary of Contents for Cube Series

Reviews:

Related manuals for Cube Series

Brands by name

Popular brands