Friulinox Cube Series Service Manual Download

Page: 20 / 89

“go to

TABLE OF CONTENTS

”

FRIULINOX ALI GROUPS.R.L. A SOCIO UNICO

Via Treviso,4 - 33083 Taiedo di Chions (PN) -Italy

Servi

ELECTRONIC BOARD OPERATION

7.1.

Board functions

equipment

ON/OFF

KEY UP

Menu item scrolling and value increase. If no programme selected, it increases setpoint values.

KEY DOWN

Menu item scrolling and value decrease. If no programme selected, it decreases setpoint values.

MENU/ENTER

Main menu of controls or set value confirmation.

ESC

Exit from menu or interruption without saving data.

ENERGY SAVING

Access to energy saving menu.

COMPRESSOR

If flashing, compressor protection in progress.

DEFROST

If flashing, compressor protection in progress or

dripping in progress.

EVAPORATOR FAN

If flashing, fan stop in progress.

CELL LIGHT ON

If flashing, light automatically on.

DOOR OPEN

ALARM OR ERROR IN PROGRESS

Operating range

Cabinet temperature

Selected mode
Temperature setpoint/Humidity
setpoint

Energy Saving Bar

OPERATING STATUS ICONS

Operation status

Summary of Contents for Cube Series


























































































Search results

Summary of Contents for Cube Series

Reviews:

Related manuals for Cube Series

Brands by name

Popular brands

Friulinox Cube Series, Service Manual

Search results

Summary of Contents for Cube Series

Reviews:

Related manuals for Cube Series

Brands by name

Popular brands