Frigidaire GRFC2353AD Page 47 Use & Care Manual Download

Page: 47 / 52

Concern Potential Cause

Common Solution

Automatic Ice Maker (Cont’d)

Ice cubes

are freezing

together.

• Ice cubes are not being

used frequently enough

or interruption of power

for prolonged time.

• Ice cubes are hollow

(shells of ice with water

inside). The hollow

cubes break open in the

bin and leak their water

onto existing ice, which

causes it to freeze

together.

• Remove ice container and discard

ice. The ice maker will produce

fresh supply. Ice should be used

at least twice weekly to keep the

cubes separated.

• This generally occurs when the

ice maker does not get enough

water. This is usually the result of

a clogged water filter or restricted

water supply. Replace the water

filter and if the condition still

occurs check for a clogged Saddle

Valve, water valve not turned on

all the way or kinked water supply

line.

Dispenser (Ice & Water)

Dispenser

will not

dispense

ice.

• There is no ice in the

bin to be dispensed.

• The refrigerator doors

are not completely

closed.

• Dispenser paddle has

been pressed too long

and the dispenser

motor has overheated.

• See the “Ice maker is not making

any ice” section above.

• Be sure the refrigerator doors are

completely closed.

• The motor overload protector will

reset in about three minutes and

then ice can be dispensed.

Ice

dispenser is

jammed.

• Ice has melted and

frozen around auger

due to infrequent

use, temperature

fluctuations, and/or

power outages.

• Ice cubes are jammed

between ice maker and

back of ice container.

• Remove ice container, thaw,

and empty the contents. Clean

container, wipe dry, and replace in

proper position. When new ice is

made, dispenser should operate.

• Remove ice cubes that are jamming

the dispenser.

Dispenser

will not

dispense

water.

• Water filter not seated

properly.

• Water filter is clogged.

• Household water line

valve is not open.

• Remove and reinstall the water

filter. For PurePour, be sure to push

the filter in all the way until it clicks

into place and is secured inside of

the water filter housing.

• Replace filter cartridge. Be sure

to push filter all the way in until

it clicks into place and is secured

inside of the water filter housing.

• Open household water line

valve. See CONCERN column

AUTOMATIC ICE MAKER.

TROUBLESHOOTING

Summary of Contents for GRFC2353AD





















































Search results

Summary of Contents for GRFC2353AD

Reviews:

Related manuals for GRFC2353AD

Brands by name

Popular brands

Frigidaire GRFC2353AD, Use & Care Manual

Search results

Summary of Contents for GRFC2353AD

Reviews:

Related manuals for GRFC2353AD

Brands by name

Popular brands