manualshive.com logo in svg

Frick IDC3-0406, Manual

Share
Download
Frick IDC3-0406 Manual Download Page 11

140.960-IOM (JUN 2016)

Page 11

IDCF & IDC3 EVAPORATIVE CONDENSERS

INSTALLATION

Figure 16 – Fan Cowl Extensions

Detail A

3/8” x 1 1/4” Bolt

3/8” Flatwasher

3/8” Locknut

Motor Removal Davit

IDCF-0709, -0718, and IDC3-7409, -7418 (See Fig. 17)
1.  Remove the cover plate from the upper support channel.
2.  Rotate the davit assembly to align the bolt head on the 

davit with the keyway in the upper support channel and 
lower into position. The davit must pass through the  
upper and lower support channel and rest on support base.

Cover Plate
(Remove)

Upper Support 

Chanel

Lower Support 

Chanel

Lower Into

Position

Figure 17 – Motor Removal Davit Installation for 

IDCF-0709, -0718, and IDC3-7409, -7418

IDCF/IDC3-1012, 1024, 2012, 1212, 2412, 1224, 2424, 1218, 

1236, 2418, AND 2436 AND IDC3-1220

1.  Verify the davit support is factory installed next to the access 

door. If not installed, remove the bolts next to the access door 
(refer to  Figure 18b). DO NOT REMOVE TAPPERS. Secure the 
davit support by re-installing the bolts.

2.  Rotate the davit assembly to align the bolt head on the davit 

with the keyway in the upper support channel and lower into 
position. The davit must pass through the upper and lower 
support channels and rest on the support base.

Figure 18a. Motor Removal Davit Installation

Figure 18b. Davit Support Detail

Bolt, Nut, 
and Washer

Tapper 
DO NOT  
REMOVE

Access Door

 CAUTION

Do not remove tappers during installation of motor removal 

davit support. Removing tappers will cause the interior 

mechanical system to fall.

Summary of Contents for IDC3-0406





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands