Freggia DWCI4108, User Manual

Page: 8 / 72

WATER INLET HOSE
Do not use the water inlet hose of your old machine, if any. Use
the new water inlet hose supplied with your machine instead. If
you are going to connect a new or long-unused water inlet hose
to your machine, run water through it for a while before making
the connection. Connect the water inlet hose directly to the water
inlet tap.The pressure supplied by the tap should be at a minimum
of 0.03 Mpa and and at a maximum of 1 Mpa.
If the water pressure is above 1 Mpa, a pressure-relief valve should
be fi tted inbetween. After the connections are made, the tap
should be turned on fully and checked for water tightness. For
the safety of your machine, make sure to always turn off the water
inlet tap after each wash programme is fi nished.
NOTE:
Aquastop water spout is used in some models.
In case of using Aquastop, a dangerous tension
exists. Do not cut Aquastop water spout. Do not
let it get folded or twisted.
WATER OUTLET HOSE
The water drain hose can be connected either
directly to the water drain hole or to the sink
outlet spigot. Using a special bent pipe (if
available), the water can be drained directly
into the sink via hooking the bent pipe over the
edge of the sink.
This connection should be at a minimum of 50
cm and and at a maximum of 110 cm from the
fl oor plane.
WARNING!
When a drain hose longer than 4 m is used, the dishes might remain dirty. In
that case, our company will not accept responsibility.
ELECTRICAL CONNECTION
The earthed plug of your machine should be connected to an earthed outlet
supplied by suitable voltage and current. If there is no earthing installation, have
a competent electrician carry out an earthing installation. In case of usage without
earthing installed, our company will not be responsible for any loss of usage that
might occur.
The indoor fuse current value should be 10-16 A.
Your machine is set according to 220-240 V. If the mains voltage in your location
is 110 V, connect a transformer of 110/220 V and 3000 W inbetween. The machine
should not be plugged in during positioning.
Always use the coated plug supplied with your machine.
Running in low voltage will cause a decline in washing quality.
The machine’s electrical cable should be replaced by an authorised service or an
authorised electrician only. Failure to do so may lead to accidents.
For safety purposes, always make sure to disconnect the plug when a wash
programme is fi nished.
In order not to cause an electric shock, do not unplug when your hands are wet.
When disconnecting your machine from the mains supply, always pull from the plug.
Never pull the cord itself.
PRIOR TO USING THE MACHINE FOR THE FIRST TIME
• Check whether the electricity and supply water specifi cations match the
values indicated by the installation instructions for the machine.
• Remove all packaging materials inside the machine.
• Set the water softener.
• Add 1 kg salt into the salt compartment and fi ll with water up to a level at
which it will almost overfl ow.
• Fill the rinse aid compartment.
ter the fi rst wash; certain crystal
items as they lose their transpar-
ency over time, adhered cutlery
that is not heat-resistant, lead
crystal glasses, cutting boards,
items manufactured with syn-
thetic fi bre;
• Absorbent items as sponges or
kitchen rags are not suitable for
dishwashing.
WARNING!
Take care to buy dishwash-
er-proof sets in your future pur-
chases.
INSTALLING THE MACHINE
POSITIONING THE MACHINE
When determining the place to put your machine on, take care to choose a place
where you can easily load and unload your dishes.
Do not put your machine in any location where there is the probability for the room
temperature to fall below 0°C.
Before positioning, take the machine out of its packaging by following the warnings
located on the package.
Position the machine close to a water tap or drain. You need to site your machine,
taking into consideration that its connections will not be altered once they are made.
Do not grip the machine by its door or panel in order to move it.
Make sure that the water inlet and outlet hoses do not get squeezed while positioning
the machine. Also, make sure that the machine does not stand on the electrical cable.
Adjust the machine’s adjustable feet so that it can stand level and balanced. Proper
positioning of the machine ensures problem-free opening and closing of its door.
If the door of you machine does not close properly, check if the machine is stable
on the fl oor it stands; if not, adjust the adjustable feet and ensure its stable position.
WATER CONNECTION
Be sure that the indoor plumbing is suitable for installing a dishwasher. Also, we
recommend that you fi t a fi lter at the entrance of your place or apartment so as to
avoid any damage to your machine because of any contamination (sand, clay, rust
etc.) that might be occasionally carried in through the mains water supply or the
indoor plumbing, and to forestall such complaints as yellowing and formation of
deposits after washing.
8
SAFETY INFORMATION AND RECOMMENDATIONS
SAFETY INFORMATION AND
RECOMMENDATIONS