background image

FreeWave Technologies 

 

HT Ethernet Addendum 

  

900MHz 

  

V1.0h 

 

Glossary of Terms: 

 

Ethernet Modem: 

The entire FreeWave modem, which includes a Radio Modem 
and an Ethernet Interface. 

 
Ethernet Bridge: 

A bridge between two Ethernet LANs, using an Ethernet modem 
at each end. 

 
Radio Modem: 

The radio portion of the Ethernet Modem.  It communicates with 
other radio modems. 

 
Ethernet Interface: 

The Ethernet portion of the Ethernet Modem.  It translates and 
filters data between the LAN and the Radio Modem. 

 
Radio Link: 

The link between FreeWave radios. 

 
LAN: 

(Local Area Network):  A computer network, such as Ethernet. 

 
Collision: 

The condition when one LAN device tries to transmit while 
another device is already transmitting. 

 
NIC: 

(Network Interface Card):  A device that translates between a 
LAN and a computer, typically found inside a personal computer. 

 
Switch: 

A smart device for connecting many Ethernet devices together. 

 
Router: 

A smart device for directing the Ethernet packets from one 
network to another. 

 
Hub: 

A dumb device for connecting many Ethernet devices together. 

 
Ethernet Device: 

Any device that attaches to an Ethernet LAN, typically using an 
RJ45 connector. 

 

Asymmetric Data 

Data that flows primarily in one direction. 

LAD0013AB Rev H 

11 of 11 

Summary of Contents for HT-900 Series












Reviews: