background image

 FreeStyle Service Manual     MN126-1 

E

 

1-2

 

1.2     Important Notice and Symbol Explanations 

As you review both the 

FreeStyle 

Patient Manual 

and this 

FreeStyle 

Service

 

Manual, 

pay special attention to the WARNING, CAUTION, and NOTE messages.

 

They identify safety guidelines or other important information as follows:

 

DO NOT OPERATE THIS EQUIPMENT WITHOUT FIRST READING AND UNDERSTANDING THIS 
MANUAL. IF YOU ARE UNABLE TO UNDERSTAND THE WARNINGS AND INSTRUCTIONS, 
CONTACT YOUR EQUIPMENT PROVIDER BEFORE ATTEMPTING TO USE THIS EQUIPMENT; 
OTHERWISE, INJURY OR DAMAGE MAY RESULT. 

Smoking while using oxygen is the number one cause of fire injuries and 
related deaths.  You must follow these safety warnings: 

Do not allow smoking, candles, or open flames in the same room with the device or 
within 5 feet (1.52 meters) of the oxygen-carrying accessories.  

Smoking while wearing an oxygen cannula may cause facial burns and possibly death. 

Removing the cannula and putting it on bedding, sofas, or other cushion material will 
cause a flash fire when exposed to a cigarette, heat source, or flame.  

If you smoke, these 3 steps may save your life: 
turn off the oxygen concentrator, take off the cannula, and leave the room where this 
device is located.  

Warning  –  

Describes  a hazard or unsafe practice that if not avoided can result in severe 

bodily injury, death or property damage 

Caution  –  

Describes a hazard or unsafe practice that if not avoided can result in minor 

bodily injury or property damage 

Note – Provides information important enough to emphasize or repeat 

“No Smoking – Oxygen in Use” signs must be prominently displayed in the home, or 
where the oxygen concentrator is in use. Patients and their caregivers must be informed 
about the dangers of smoking in the presence of, or while using, medical oxygen.  

Summary of Contents for MN126-1


































































Reviews: