background image

9

          NOTE

-The battery and charger of FREERIDE X2 HUB are matched. Therefore, never charge the batteries with 
a charger other than the supplied charger.
-The maximum battery life is achieved by charging them at ambient temperature b10 degrees 
and max. +30 degrees.
-The batteries can warm up when they are under heavy pressure. Please note room temperature before 
loading.

          NOTE

As a consumer, you are legally obliged to return used batteries and batteries to designated collection 
points. You can drop your spent batteries and batteries at the public collection points in your municipality 
or anywhere where batteries and batteries of that type are sold. 

Batteries and batteries don't belong in 

in the trash.

8.1. Fuse

The battery system is protected by a plug -in fuse. Replacement fuses can be found in the supplied 
toolbox if required. On the fuse you will find the specification printed.

8.2. Battery Capacity / Type

FREERIDE X2 HUB: 60V 20Ah Lithium batteries.
Use only the high quality original batteries of the same quality. If you need replacement batteries, 
please contact your dealer.

8.3. Use of batteries

New batteries must always be fully charged the first five times. The more you charge your batteries, the 
better. They save batteries if they are not discharged below 20% residual capacity. Never charge batter-
ies at minus degrees -let the batteries at minus degrees warm up to room temperature before charging 
them. This considerably prolongs the service life.

8.4. Charging device

          In order to prevent risks of injury, you must only charge the supplied and installed battery with the 
charger.
Other batteries could explode if charged. The use of accessories or batteries that are not sold or recom-
mended by us may lead to fire risk, electric shock or other serious injuries.
In any case, avoid operating the charger in a humid or wet environment. Avoid any water entering the 
device. If there is any liquid, disconnect the charger immediately from the mains and have it checked by 
the specialist.
The device should be safe and level. Always disconnect the device from the mains if not in use. Never 
pull on the cable, as this avoids cable damage and the risk of electrocution.
Never operate the charger with damaged cable or plug or with damage to the plastic housing. Do not 
dismantle or open the charger yourself under any circumstances. Any manipulation or incorrect assembly 
may result in an electric shock or fire.

Summary of Contents for X2 HUB





















Reviews: