background image

Freedom Lite Installation Manual Revision 12 

 

                        P a g e  

1 | 30

 

 

1.

 

Introduction 

This manual is intended to provide assistance to an installer for the installation and 
commissioning of the range of 

Freedom Lite

 lithium iron phosphate (LiFePO4) energy 

storage modules. This document is not intended to provide detailed information of the 
inner workings of Freedom Lite that is not relevant to a person that is performing the 
installation and final commissioning. Supplementary information relating to programming of 
the built-in battery management system for specific applications is available to approved 
integrators directly from Freedom Won.  

This manual does not attempt to cover all the details pertaining to the setup of third-party 
equipment in relation to the interface and necessary functionality to work with the Lite. 
Freedom Won however is available at the contact details on page one to provide direct 
support where necessary for supported third party brands.  

 

2.

 

Product Description 

The Freedom Lite technology is available in various standard sizes to meet all residential, 
commercial and industrial applications, ranging in models from 5kWh up to 2500kWh. 
Larger systems are provided by Freedom Won based on specific project requirements by 
installing multiple units in parallel.  

Freedom Won offers the following ranges in the LiFePO4 technology: 

1.

 

Lite 12V 

2.

 

Lite Home and Business 

3.

 

Lite HV Home and Business 

4.

 

Lite Marine 

5.

 

Lite Mobility (golf carts, forklifts etc)  

6.

 

Lite Commercial (including Lite Commercial HV and HV+) 

7.

 

Lite Industrial 

This manual covers the standard voltage models of the 

Lite Home and Business

 range from 

5kWh up to 80kWh. Please refer to the manuals specific to the other ranges.   

The standard Lite voltage is 52V nominal (to suit 48V systems). The Freedom Lite HV range is 
designed for specific 

H

igher 

V

oltage inverters such as those from Ingeteam (Ingecon 1Play 

3TL and 6TL). The Lite Commercial range varies from 52V to 800V depending on customer 
requirements (including the HV and HV+ models). The Industrial range varies from 
approximately 500V to 800V depending on customer requirements.  

The Lite Marine range of lithium batteries is available on request with similar specifications 
to the Home range including 13V and 26V options to suit 12V and 24V systems respectively. 
These models are water resistant (IP65) and designed for mounting on the floor or 
horizontal deck and have dimensions that are different to the Lite Home models. For more 
information on these models please contact Freedom Won. 

Summary of Contents for Lite Business 40/32































Reviews: