manualshive.com logo in svg

Freedom Lite Business 40/32, Installation Manual, Page: 16 / 30

Share
Download
Freedom Lite Business 40/32 Installation Manual Download Page 16

Freedom Lite Installation Manual Revision 12 

 

                        P a g e  

15 | 30

 

 

The third-party device manuals must be referenced for all details regarding connecting the 
CAN interface. 

Most brands use 500kbps. If 250kbps is required it is available on the Lite with a specific 
profile loaded, which must be requested when ordering the Lite or can be loaded during 
commissioning by your distributor for Freedom Won technical support.  

If you did not purchase a CAN Bus cable to suit your inverter you can make your own 
according to Table 4.2. Fig 4.1 provides the standard colour coding for an Ethernet cable 
(note that there are other variations so double check this).  

 

Fig 4.1 Pin Configuration for standard RJ45 plug 

 

Table 4.2 Pin Configuration for CAN Bus Control Cable for various supported inverters 

Wire 
Function 

Standard 
Lite and 
Victron 

SMA 

Ingeteam 

Imeon 

Solax 

Goodwe 

Sofar 

CAN 
Low 

Pin 8 
(brown) 

Pin 5 (blue/ 
white) 

Labelled 
on inverter 

Pin 2 
(orange) 

Pin 1 
(orange/ 

white) 

Pin 5 
(blue/ 

white) 

Pin 2 
(orange) 

CAN 
High 

Pin 7 
(brown/ 
white) 

Pin 4 (blue) 

Pin 1 
(orange/ 
white) 

Pin 2 
(orange) 

Pin 4 
(blue) 

Pin 1 
(orange/ 
white) 

 
 

. 

 

Bridge Pin 3 and 
Pin 6 on Inverter 

end or cable with 
a 120Ω resistor 

 
 

 

 

 

 

 

If your inverter is not included in this table, please contact Freedom Won for assistance.  

4.4

 

Parallel Configurations 

It is permissible to connect multiple Freedom Lite’s in parallel provided that the Freedom 
Lite model size used is the same throughout. It is however more cost effective to purchase 
one larger Freedom Lite model than connecting multiple units in parallel. This type of 

Summary of Contents for Lite Business 40/32































Reviews:

No comments