Freedom Lite Business 40/32 Installation Manual Download | Manualshive

Page: 11 / 30

background image

Freedom Lite Installation Manual Revision 12

P a g e

10 | 30

The units can alternatively be lifted to the right height and onto the hanging bolts using a
high-lift pallet jack such as shown in Figure 3.4. A site assembled gantry with electric winch
is shown in Figure 3.5. This gantry is available from Freedom Won as an accessory and is
available with various gantry widths.

Figure 3.4 High Lift Pallet Jack

Models up to Lite Home 20/16 are fitted with lifting or manoeuvring handles to make
placement easier. See Fig 4.2.

«
...
9
10
11
12
13
...
»

Summary of Contents for Lite Business 40/32































Reviews:

No comments

Related manuals for Lite Business 40/32

Brand: CAB Pages: 10

Brand: Samsung Pages: 21

Brand: JANE Pages: 6

Brand: Baja Designs Pages: 6

Brand: Bachmann Pages: 2

AdvancedPunch Pro

Brand: GBC Pages: 92

Brand: IFM Pages: 12

Brand: IFM Pages: 13

Efector 200 Series

Brand: IFM Pages: 4

Brand: IFM Pages: 33

Brand: Nautronic Pages: 7

Brand: NAPCO Pages: 16

Brand: Omega Engineering Pages: 2

Brand: Oki Pages: 52

Brand: S&B Filters Pages: 7

Brand: Tascam Pages: 4

Brand: Tascam Pages: 2

Brand: Tascam Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands