manualshive.com logo in svg

FRC TCA200, Manual

Share
Download
FRC TCA200 Manual Download Page 7

TCA200 Rev171031

7

High Idle Wiring

The programming includes a high idle function. To activate the high idle provide 

a +12 VDC  High Idle Active Input. (Refer to Figure 8. High Idle Wiring.)

Note:

 It is important that the connection to the Interlock Input from the High 

Idle circuit be isolated from the apparatus interlock wiring with the two 

diodes. Refer to the wiring diagram. 

The pump must NOT be engaged 

when using the high idle function.

The high idle is set at about 1000 RPM at the factory. (This value will vary 

depending on the specific engine.) To adjust this setting refer to High Idle in the 

Operation Section.

Cables

There are two connectors on the control module for all input/output signals, one 

8-pin connector and one 12-pin connector.

When replacing an older Detroit Diesel governor, connectors with wiring are 

provided to utilize some of the existing harness. New wiring is required for the intake 

pressure sensor and engine control. Refer to the Wiring Section.

Summary of Contents for TCA200

































Reviews:

No comments

Brands by name

Popular brands

Load more brands