manualshive.com logo in svg

FRC TCA200, Manual

Share
Download
FRC TCA200 Manual Download Page 13

TCA200 Rev171031

13

Table 2.  Error Codes

Table 3.  Fault Warning Codes

RPM 

Display

Message 

Display

Probable Cause

Note:

 Not all inputs are used for all engines. For systems that use 

a datalink to pass information the datalink cable and connectors or 

ECM programming would be the probable cause.

E01

No Data

>Datalink cable not connected / connected to wrong port

>Broken wire / bad connector contact on datalink cable

E02

No RPM

Engine RPM not detected

>Datalink cable not connected / connected to wrong port

>Engine not running / ignition key on

E03

No Trans T. 

Sensor

No Transmission Data Detected

>Datalink cable not connected / connected to wrong port

>Broken wire / bad connector contact on datalink cable

E04

No Eng Oil 

Sensor

No Engine Oil Pressure Data Detected

>Datalink cable not connected / connected to wrong port

>Broken wire / bad connector contact on datalink cable

E05

No D.  

Sensor

No Discharge Pressure Sensor Detected

>Sensor cable not connected

>Broken wire / bad connector contact on sensor cable

>Defective pressure sensor

E06

No I.   

Sensor

No Intake Pressure Sensor Detected

>Sensor cable not connected

>Broken wire / bad connector contact on sensor cable

>Defective pressure sensor

E07

No Eng 

T.Sensor

No Coolant Temperature Data Detected

>Datalink cable not connected / connected to wrong port

>Broken wire / bad connector contact on datalink cable

RPM 

Display

Message Display

Description

F01

Hi Batt

High Battery Voltage

F02

Low Batt

Low Battery Voltage

F03

Hi Trans

High Transmission Temperature

F04

Low Oil

Low Engine Oil Pressure

F07

Hi Eng T.

High Engine Coolant Temperature

F08

No Water

Out of Water Mode

F09

No Resp

Engine Does Not Respond

Summary of Contents for TCA200

































Reviews:

No comments

Brands by name

Popular brands

Load more brands