manualshive.com logo in svg

FRC TCA200, Manual

Share
Download
FRC TCA200 Manual Download Page 18

TCA200 Rev171031

18

Detailed Information

The four LED bar graphs provide a constant display of the safe operating ranges for 

engine oil pressure, engine coolant temperature, transmission temperature, and battery 

voltage. They do not show exact numbers or units of measure. Detailed information 

is shown in the message display when the 

MENU

 button is pressed. Engine hours and 

pump hours are also shown.

Show Detailed Information

Note:

 Detailed information is a display only mode and no changes can be 

made to the data.

The 

MENU

 button allows the operator to gain access to detailed information. Each 

time the 

MENU

 button is pressed the display scrolls to show the next value.

The message display will show the following:

Eng Oil      ###PSI 

 

 

(programmable for kPa or Bar)

Eng Temp      ###°F   

 

(programmable for °C)

Trans T.      ###°F 

 

 

(programmable for °C)

Batt VDC      ##.#
Eng Hrs      ####
Pump Hrs      ####

The message display reverts to normal operation after 20 seconds if no buttons are 

pressed or immediately when a button other than the 

MENU

 button is pressed.

Summary of Contents for TCA200

































Reviews:

No comments

Brands by name

Popular brands

Load more brands