manualshive.com logo in svg

Franklin Fueling Systems EVO 600, Programming Manual, Page: 79 / 86

Share
Download
Franklin Fueling Systems EVO 600 Programming Manual Download Page 79

73

Alarm/Warning 

Device

Description

Recommended Actions

Time source 

error

NONE           

Too few bytes 

error

TANK     

Too many floats

TANK     

# of floats detected on 

probe is more than what 

is programmed in the ATG

Verify configuration programming is set to the 

actual number of floats on the probe.

Ullage error

Tank

Ullage reported has 

exceeded tank capacity.

Check for proper probe and tank programming 

at the console. If programming is correct, 

inspect the probe to ensure that the float is 

not stuck in the riser or obstructed. Bring the 

probe inside and wire directly to the gauge 

to eliminate possible problems with the field 

wiring. 

Unbalanced 

Load

TPI

The STP controller is 

reporting an unbalanced 

load condition.

Refer to the applicable Smart Controller 

Installation guide for details.

Unbalanced 

Voltage

TPI

The STP controller is 

reporting an unbalanced 

voltage condition.

Refer to the applicable Smart Controller 

Installation guide for details.

Under Load

TPI

The STP controller is 

reporting an underload 

condition.

Refer to the applicable Smart Controller 

Installation guide for details.

Under Voltage

TPI

The STP controller is 

reporting a voltage level 

under 200VAC.

Refer to the applicable Smart Controller 

Installation guide for details.

Unexpected 

reset

NONE           

Unknown

NONE           

Unknown Fault

TPI

The STP controller is 

reporting an unknown 

fault code.

Check fault condition on Smart controller 

and contact FFS Technical Services for more 

information    

Unstable probe

Tank

LL Liquid Level probes can 

send inconsistent data 

back to console.

Check for proper probe programming at the 

console and inspect wire connections at the 

probe. If the problem persists, contact FFS 

Technical Services for support. 

Vapor detected

SENSOR   

A discriminating sensor 

has detected vapor.

Check location where sensor detected vapor.

Watchdog reset

NONE           

Water present

SENSOR   

A discriminating sensor 

has detected the liquid 

present is water.

Check containment for collection of water.  

Troubleshoot source of the leak.

Water volume 

error

Tank

Water volume has 

exceeded tank capacity.

Check for proper probe and tank programming 

at the console. If programming is correct, 

inspect the probe to ensure that the colored 

water float is on the bottom.

Web server 

error

NONE           

Wire Sensor 

Alarms

Summary of Contents for EVO 600























































































Reviews:

No comments