EN
2
20
USE
Control panel
-When power is supplied to the hood, LED
A
flashes for approximately 10 seconds; during this time the interface is not enabled.
-When the control panel functions are not active only button
A
can be seen. When this is pressed all the other commands become visible.
-The functions selected are shown by backlighting the button at maximum intensity, while the other buttons are lit at reduced intensity.
-If all the functions are off the panel will switch off after 30 seconds, or when button
A
is pressed.
Button Function
Display
Press briefly to turn the motor Off.
The LED on button
A
is on fixed (when the
motor is on)
A
Press and hold the button for approximately 4 seconds, with all the loads turned off
(Motor and Lights) and no alarms triggered, to turn the Remote control on/off.
The procedure can be activated with the door in any position.
The LEDs on buttons
A
and
B
flash twice to
indicate that the remote control is on;
The LEDs on buttons
A
and
B
flash once to
indicate that the remote control is off;
Press briefly to activate speed one.
LED on button
B
is on fixed
B
Press and hold for 2 seconds to activate the 24H function in which the motor turns
on at a speed that allows suction for 10 minutes every hour; at the end of the
24h
the function is deactivated.
To deactivate it, press and hold button
B
again for 2 seconds, or press button A or
button
H
.
LED on button
B
flashes (every 0.5 seconds
during the 10 minutes on and every 2 seconds
during the 50 minutes off)
C
Activates speed two.
LEDs on buttons
C
and
A
are on fixed
D
Activates speed three.
LEDs on buttons
D
and
A
are on fixed
Press briefly to activate speed four.
LEDs on buttons
E
and
A
are on fixed
E
Press and hold for 2 seconds to activate Intensive speed. This speed is timed to run
for 10 minutes. At the end of this time the system will automatically return to the
speed set before.
Cannot be activated if the
Delay
or
24H
functions are active.
It is disabled by pressing any of the Speed buttons or turning the Motor off.
LED on button
E
on (flashes every second) and
LED on button
A
on fixed
Press briefly to turn the
DELAY
on/off, this enables automatic shutdown of the
Motor and the Lighting with a 30’ delay.
Can be activated with the motor on (unless
intensive
or
24H
is running).
LED on button
F
on fixed if the function is
activated
Press and hold the button for approximately 4 seconds, with all the loads turned off
(Motor and Lights), to turn the Activated Charcoal Filter alarm on.
To turn it off, press and hold the button again for 4 seconds.
The LEDS on buttons
F
and
B
flash twice
The LEDS on buttons
F
and
B
flash once
F
With the filter alarm triggered, press the button briefly to Reset the alarm.
These signals are only visible with the motor turned off and the control panel active.
The Reset is signalled by the fact that LED
F
turns off.
After 100 hours operation the Led on button
F
lights up continuously to indicate saturation of
the Metal Grease Filters.
After 200 hours in operation the Led on button
F
flashes to indicate saturation of the Activated
Charcoal filters.
Press briefly to turn the Secondary Lights (spotlights) on and off at maximum
intensity.
The button is also active with the door closed.
LED on button
G
is on fixed
G
Press and hold the button for 2 seconds to turn the Courtesy Lights On
LED on button
G
is on fixed
H
Door Closed:
- Press and hold for approximately 2 Seconds to open the door, turn the motor on at
the last speed set and turn the Main lights (LEDs) on.
Door Open:
- Press briefly to turn the Main lights (LEDs) On or Off.
- Press for 2 seconds to turn everything off (Motor and Main lights) and close the
door.
LED on button
H
is on fixed when the main
lights are turned on.
A
B
C
D
E
F
G
H