background image

STEP 5

Connect the boards for your second level in the quantity and orientation as shown below. 

1. 

Connect 

2

x 4ft Curved Boards with Stacking Brackets on 

on both ends in alternating orientation.

2. 

Connect 

x 4ft Curved Board with a top-section

4-way bracket on one end and a stacking bracket on 
the other end in alternating positions as shown to 
the right .

3. 

Connect 

4

x 4ft Curved Boards with a stacking bracket 

on one end and a top 4-way bracket on the other end
in alternating orientation as shown to the right.

4. 

Connect 

x 4ft Curved boards with a stacking bracket  

on end and a top-section 4-way bracket on the other end

in the same position.

5. 

Connect 

x 4ft Curved board with stacking brackets on 

both sides in the top position.

6. 

Connect 

each of the curved 

gate boards 

with 

stacking brackets on one end in the down
position.

7

. Connect 

x 4ft Curved Board with a top-section 4-way

bracket on one end and a stacking bracket on the other
end in the same position.

8. 

Connect 

4

x 2ft Boards with mid-section 4-way brackets on

both ends in alternating orientation.

9. 

Connect

x 2ft Boards with a stacking bracket on one end

and a top section 4-way bracket on the other end in 
alternating orientation.

ASSEMBLY INSTRUCTIONS 

Level 1 Continued

Step 2

: Layout the Boards for the first level according to the number of the 

board in Step 1. 

Note:

It is especially important to layout the boards in the exact orientation 

shown in the diagram below.

The gate Board (

Board 3

) on level 1 is kept uncut to act as a level surface for the 

gate to swing on. You can choose to cut this Board if you want it to be apart of the 
swinging gate. 

IMPORTANT

: If you connect any brackets incorrectly, they can be removed by 

inserting a flathead screwdriver into the opening of the snap-lock plugs, pushing into 
the nub and twisting upwards.  

Step 3:

When connecting the boards for the first level, insert the anchor 

stakes upside down so the stake is pointing to the sky. This will allow you to 
adjust the shape of your frame before driving the stakes into the ground. 

Step 4:

Once you finish with the adjustments of your base level frame, flip 

over the stakes and hammer them into the ground. 

1

1

1

1

1

1

1

1

1

6

1

2

2

3

4

5

1

2

3

4

5

6

6

7

9

8

Summary of Contents for RAISED GARDEN BED






Reviews: