Four-Faith F-NR130 User Manual Download Page 73

Page: 73 / 81

www.fourfaith.com

Copyright @ Four-Faith 2021

F-NR130 User Manual

MAC Address:

MAC address of wireless client

Interface:

Interface of wireless client

Uptime:

Connecting uptime of wireless client

TX Rate:

Transmit rate of wireless client

RX Rate:

Receive rate of wireless client

Signal:

The signal of wireless client

Noise:

The noise of wireless client

SNR:

The signal to noise ratio of wireless client

Signal Quality:

Signal quality of wireless client

Neighbor's Wireless Network:

Display other networks nearby

SSID:

The name of wireless network nearby

Mode:

Operating mode of wireless network nearby

MAC Address:

MAC address of the wireless nearby

Channel:

The channel of the wireless nearby

Rssi:

Signal intensity of the wireless nearby

Noise:

The noise of the wireless nearby

Beacon:

Signal beacon of the wireless nearby

Open:

The wireless nearby is open or not

Dtim:

Delivery traffic indication message of the wireless nearby

Rate:

Speed rate of the wireless nearby

Join Site:

Click to join wireless network nearby

Summary of Contents for F-NR130


















































































Search results

Summary of Contents for F-NR130

Reviews:

Brands by name

Popular brands

Four-Faith F-NR130, User Manual

Search results

Summary of Contents for F-NR130

Reviews:

Brands by name

Popular brands