Four-Faith F-NR130 User Manual Download

Page: 24 / 81

www.fourfaith.com

Copyright @ Four-Faith 2021

F-NR130 User Manual

Status

DDNS Status shows connection log information

Clone MAC Address

Some ISP need the users to register their MAC address. The users can clone the Router
MAC address to their MAC address registered in ISP if they do not want to re-register

their MAC address

Clone MAC address:

Can clone three parts: Clone LAN MAC, Clone WAN MAC, Clone

Wireless MAC.

Noted:

That one MAC address is 48 characteristics, cannot be set to the multicast address,

the first byte must be even. And MAC address value of network bridge br0 is determined

by the smaller value of wireless MAC address and LAN port MAC address.

Advanced Router

Operating Mode:

Gateway and Router

If the Router is hosting users' Internet connection, select Gateway mode. If another
Router exists on their network, select Router mode.

Summary of Contents for F-NR130


















































































Search results

Summary of Contents for F-NR130

Reviews:

Related manuals for F-NR130

Brands by name

Popular brands

Four-Faith F-NR130, User Manual

Search results

Summary of Contents for F-NR130

Reviews:

Related manuals for F-NR130

Brands by name

Popular brands