Four-Faith F-NR130 User Manual Download

Page: 68 / 81

www.fourfaith.com

Copyright @ Four-Faith 2021

F-NR130 User Manual

WAN

Connection Type:

Disabled, static IP, automatic configuration-DHCP, PPPOE, PPTP,

L2TP, 3G/UMTS

DHCP-4G/5G

Connection Uptime:

Connecting uptime; If disconnect, display Not available

IP Address:

IP address of router WAN

Subnet Mask:

Subnet mask of router WAN

Gateway:

The gateway of router WAN

DNS1, DNS2, DNS3:

DNS1/DNS2/DNS3 of Router WAN

Remaining Lease Time:

Remaining lease time of IP address in DHCP way

DHCP Release:

Release DHCP address

DHCP Renew:

Renew IP address in DHCP way, default is 1 day

Login Status:

Connection status of WAN

Disconnection:

Disconnect

Connection:

Connect

Module Type:

Module type in 3G/UMTS way

Signal Status:

Signal intensity of the module in 3G/UMTS way

Network:

Network type of the module in 3G/UMTS way

Summary of Contents for F-NR130


















































































Search results

Summary of Contents for F-NR130

Reviews:

Related manuals for F-NR130

Brands by name

Popular brands

Four-Faith F-NR130, User Manual

Search results

Summary of Contents for F-NR130

Reviews:

Related manuals for F-NR130

Brands by name

Popular brands