Four-Faith F-NR130 User Manual Download

Page: 46 / 81

www.fourfaith.com

Copyright @ Four-Faith 2021

F-NR130 User Manual

GRE Tunnel:

Enable or disable GRE function

Number

：

Switch on/off GRE tunnel app

Status

：

Switch on/off someone GRE tunnel app

Name

：

GRE tunnel name

Through

：

The GRE packet transmit interface

Peer Wan IP Addr

：

The remote WAN address

Peer Subnet

：

The remote gateway local subnet, eg: 192.168.1.0/24

Peer Tunnel IP

：

The remote tunnel IP address

Local Tunnel IP

：

The local tunnel IP address

Local Netmask

：

Netmask of local network

Keepalive

：

Enable or disable GRE Keepalive function

Retry times

：

GRE keepalive detect fail retries

Interval

：

The time interval of GRE keepalive packet sent

Fail Action

：

The action would be exec after keeping alive failed Click on

“

View GRE tunnels

” keys can view the information of GRE

Summary of Contents for F-NR130


















































































Search results

Summary of Contents for F-NR130

Reviews:

Related manuals for F-NR130

Brands by name

Popular brands

Four-Faith F-NR130, User Manual

Search results

Summary of Contents for F-NR130

Reviews:

Related manuals for F-NR130

Brands by name

Popular brands