Four-Faith F-NR130 User Manual Download

Page: 38 / 81

www.fourfaith.com

Copyright @ Four-Faith 2021

F-NR130 User Manual

Note:

Client IP must be different with IP assigned by Router DHCP.

The format of CHAP Secrets is user * password *.

L2TP Client

Gateway (L2TP Server):

L2TP server’s IP Address or DNS Name

Remote Subnet:

The network of remote PPTP server

Remote Subnet Mask:

Subnet mask of remote PPTP server

MPPE Encryption:

Enable or disable Microsoft Point-to-Point Encryption

MTU:

Maximum transmission unit

MRU:

Maximum receive unit

NAT:

Network address translation

Username:

Username to login L2TP Server

Password:

Password to login L2TP Server

Require CHAP:

Enable or disable support chap authentication protocol

Refuse PAP:

Enable or disable refuse to support the pap authentication

Require Authentication:

Enable or disable support authentication protocol

Summary of Contents for F-NR130


















































































Search results

Summary of Contents for F-NR130

Reviews:

Related manuals for F-NR130

Brands by name

Popular brands

Four-Faith F-NR130, User Manual

Search results

Summary of Contents for F-NR130

Reviews:

Related manuals for F-NR130

Brands by name

Popular brands