background image

Foundry ServerIron Hardware Installation Guide

4 - 24

© 2008 Foundry Networks, Inc.

October 2008

Regulatory Compliance

This section contains regulatory standards for the power supplies.

FCC CFR 47 Part 15 Warning 

WARNING: This equipment has been tested and found to comply with the limits for a Class A digital device, pur-
suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and 
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may 
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to 
cause harmful interference in which case users will be required to correct the interference at their own expense.

CAUTION:

Changes or modifications made to this device which are not expressly approved by Foundry Net-

works could void the user’s authority to operate the equipment.

CISPR 22 CLASS A Warning

WARNING: This is a class A product. In a domestic environment this product may cause radio interference in 
which case the user may be required to take adequate measures.

VCCI

WARNING: This is a Class A product based on the standard of the Voluntary Control Council for Interference by 
Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance 
may arise. When such trouble occurs, the user may be required to take corrective actions.

For Japan:

Industrial Use

WARNING: This Class A Device is registered for EMC requirements for industrial use. The seller or buyer should 
be aware of this. If this type was sold or purchased by mistake for residential use, it should be replaced with a res-
idential-use type. 

For Korea:

Summary of Contents for ServerIron 4G



























Reviews: