- 36 -
- 37 -
of the top cabinet) of the bottom board of the
top cabinet shall be deemed as the location
datum. And the distance between the upper
edge and the center of the bracket shall be 7
11/16"(194.4mm) for 6"(152.4mm) decorative
sheet and 5 11/16"(143.6mm) for 4"(101.6mm)
decorative sheet.
The upper edge (the fixed
surface between the decorative
sheet and the board of the top
cabinet) of the bottom board of
the top cabinet shall be deemed
as the location datum.
7 11/16"
(194.4mm)
or
5 11/16"
(143.6mm)
Caution:
One of the wood screws(#10×2
9/16"(ST5×65mm)) for main engine must be
fastened to the beam.Screws must be fixed
at Hole A and B in the drawing; also wood
screws(#10×2 9/16"(ST5×65mm)) must be fixed
at bracket bores with corresponding wooden
stakes in Area C.
4.Fixing hooks:
1) Punch marks are on tiles (marble): Punch
holes (φ3/8"(φ8mm)) with an electric drill at
the marks, and embed expansion tube for
tiles(φ1/4"×1 5/16"(φ5.3×32mm)); fix hook with
hook screws(#8×1 7/16"(ST4.2×36mm)), and
keep the hook level with a level ruler.
2) Punch marks are on plasterboards: Screw
the expansion tube for plasterboards(φ3/16"×1
5/8"(φ4×40m)) into walls with screwdrivers at
the marks; fix hooks with hook screws(#8×1
7/16"(ST4.2×36mm)), and keep the hook
horizontal with a level ruler.
5.Place the hole-drilling template with the side
of the hole-drilling dimension drawing facing
4''(101.6mm)
5 11 /16''(143.6mm)
1.Unpack the appliance and check the List of
Accessories.
2. Locate the wooden beam and mark the
location with a pencil.
Framing Stud
3. Locate the duct bracket. Determine the
central point and mark the centerline on the
wall where the hood will be installed. Also, mark
the point where the central line and the top
cabinet meet. This is the location, in which to
secure the bracket. Mark screw hole locations
on the wall. The upper edge (the fixed surface
between the decorative sheet and the board
Caution:
Two installers are required to ensure
safe installation.
8.Use three sets of screws (#10×2 13/16"(M5×70mm))
for upper cabinet boards and supporting gaskets
(φ1 5/16"(φ32mm)) to fix the main body, and secure
at least two screws before releasing.
the bottom
board of the
top cabinet
Range hood shel
If there is a big gap between the bottom board of the
top cabinet and the top of the range hood, please
add wood pads based on the gap size near the four
#10×2 13/16"(M5×70mm) screws to avoid range
hood shell deformation caused by the tightening of
screws, which will affect the use of the range hood.
Range hood shel
the bottom
board of the
top cabinet
Wooden plate
9. Place the seal (notch downward) at the air
outlet of the machine and fix the outlet housing
with 4 outlet-housing bolts of #8×3/4"(M4×18mm).
Then, secure the duct to the duct cover and seal
the connection with aluminum tape.
10. The machine shall be kept horizontal, then
install two oil cups and plug in power to test the
machine.
Warning:
Please wear the qualified protective
gloves in operation.
Caution:
Please run the machine and test if
the smoke pipe leaks air after it is sealed with
aluminum foil tape. The smoke pipe should be
able to be straightened as much as possible.
Installation Instructions for the Decorative
Plate with Upper Cabinet :
Caution:
Please confirm the height of the top
cabinet. If the upper cabinet is over 32 1/2" es
(825mm) high, 6"(152.4mm) or 4"(101.6mm)
decorative plate is preferred.
Diameter of smoke
tube
Φ
6" (152.5mm)
Diameter of hole digging
Φ
6 1/2" (165mm)