fos4X Blackbird OECD MDE0835 Instructions For Use Manual Download Page 51

Page: 51 / 80

5. Installation

TIP

When connecting the CAN cable, make sure that the
terminating switch is in the correct position.

The correct position of the switch depends on the topology of
the CAN network.

Figure 22: CAN
connector

Connecting the CAN Interface:

Attach the cable of the CAN interface to the MC 1,5/ 3-
GF-3,81 connector.

Observe the assignment of the pins High (H), Low (L) and
Ground (G) at the CAN connector.

Connect the MC 1,5/ 3-GF-3,81 connector to the CAN
connector.

5.4 Connecting the Power Supply

TIP

The measuring device has an integrated protection against
reverse polarity.

If the polarity of the power supply is incorrect, the measuring
device is protected against damage.

Figure 23: PWR
connector

Connecting the power supply:

Switch off the power supply.

Attach the cable of the power supply to the MC 1,5/ 2-
GF-3,81 connector.

Observe the pin assignments (+) and (-) on the PWR
connector.

Connect the MC 1,5/ 2-GF-3,81 connector to the PWR
connector.

Switch on the power supply.

MDE0835_4-10_1.3.x_5.0_Blackbird

OECD_(6CH, CNO)-en-us

51 / 80

Summary of Contents for Blackbird OECD MDE0835

















































































Search results

Summary of Contents for Blackbird OECD MDE0835

Reviews:

Related manuals for Blackbird OECD MDE0835

Brands by name

Popular brands

fos4X Blackbird OECD MDE0835, Instructions For Use Manual

Search results

Summary of Contents for Blackbird OECD MDE0835

Reviews:

Related manuals for Blackbird OECD MDE0835

Brands by name

Popular brands