manualshive.com logo in svg

Fortinet FortiGate FortiGate-5001SX, Security System Manual

Share
Download
Fortinet FortiGate FortiGate-5001SX Security System Manual Download Page 32

FortiGate-5001SX   Security System Guide

32

01-30000-0380-20070201

FortiGate-5001SX base backplane data communication

Quick Configuration Guide

4

Make sure the FortiGate module can connect to the TFTP server. 

You can use the following command to ping the computer running the TFTP 
server. For example, if the IP address of the TFTP server is 192.168.1.168:

execute ping 192.168.1.168

5

Enter the following command to copy the firmware image from the TFTP server to 
the FortiGate-5001SX module: 

execute restore image <name_str> <tftp_ipv4>

Where 

<name_str>

 is the name of the firmware image file and 

<tftp_ipv4>

 is 

the IP address of the TFTP server. For example, if the firmware image file name is 

image.out

 and the IP address of the TFTP server is 192.168.1.168, enter: 

execute restore image image.out 192.168.1.168

The FortiGate-5001SX module responds with the message: 

This operation will replace the current firmware version!

Do you want to continue? (y/n)

6

Type 

y

. 

The FortiGate-5001SX module uploads the firmware image file, upgrades to the 
new firmware version, and restarts. This process takes a few minutes. 

7

Reconnect to the CLI.

8

To confirm the firmware image is successfully installed, enter: 

get system status

9

Update antivirus and attack definitions. You can use the command 

execute update-now

FortiGate-5001SX base backplane data communication

You can configure the FortiGate-5001SX modules for data communications using 
the two FortiGate-5140, FortiGate-5050, or FortiGate-5020 chassis base 
backplane interfaces.

By default the base backplane interfaces are used for HA heartbeat 
communication. However, using the information in this section, you can configure 
the FortiGate-5001SX to also use the base backplane interfaces for data 
communication. Once the base backplane interfaces are configured for data 
communication you can operate and configure them in the same way as any 
FortiGate-5001SX interface.

Although not recommended, you can use base backplane interfaces for data 
communication and HA heartbeat communication at the same time.

Note: 

Different FortiGate-5000 series modules may use different names for the base 

backplane interfaces. For example, on the FortiGate-5001SX and FortiGate-5001FA2 
modules the base backplane interfaces are called port9 and port10. On the 
FortiGate-5005FA2 module the base backplane interfaces are called base1 and base2.

Note: 

VLAN communication over the backplane is only available for FortiGate-5005FA2 

modules installed in a FortiGate-5020 chassis. The FortiSwitch-5003 does not support 
VLAN-tagged packets so VLAN communication is not available over the FortiGate-5050 
and FortiGate-5140 chassis backplanes.

Summary of Contents for FortiGate FortiGate-5001SX





































Reviews:

No comments

Brands by name

Popular brands

Load more brands