manualshive.com logo in svg

Fortinet FortiGate FortiGate-5001SX, Security System Manual

Share
Download
Fortinet FortiGate FortiGate-5001SX Security System Manual Download Page 18

FortiGate-5001SX   Security System Guide

18

01-30000-0380-20070201

Removing a FortiGate-5001SX module from a chassis

Hardware installation

1

Attach the ESD wrist or ankle strap to your wrist or ankle and to an ESD socket or 
to a bare metal surface on the chassis or frame.

2

Disconnect all cables from the FortiGate-5001SX module, including all network 
cables, the console cable, and any USB cables or keys.

3

Fully loosen the mounting knots on the left and right sides of the 
FortiGate-5001SX front panel.

4

Fully loosen the left extraction lever locking screw to unlock the left extraction 
lever.

5

Turn both extraction levers to their fully open positions.

Opening the extraction levers slides the module a short distance out of the slot, 
disconnecting the module from the chassis backplane.

The IPM LED turns blue. All other LEDs turn off.

6

Pull the module about half way out.

All LEDs turn off.

!

Caution: 

FortiGate-5001SX modules must be protected from static discharge and physical 

shock. Only handle or work with FortiGate-5001SX modules at a static-free workstation. 
Always wear a grounded electrostatic discharge (ESD) preventive wrist or ankle strap when 
handling FortiGate-5001SX modules.

Loosen

Mounting

Knot

Locking Screw

Open

Fully Open

Alignment Pin

Alignment Pin

Left Extraction

Lever

Left Extraction

Lever

Summary of Contents for FortiGate FortiGate-5001SX





































Reviews:

No comments

Brands by name

Popular brands

Load more brands