FORTEZA TRIBO-M Operation & Installation Manual Download

Page: 3 / 52

JSC FORTEZA FORTEZA TRIBO-M

Please visit our internet sites:

www.forteza.com

www.forteza.eu

Page 3

Contained in the Operation Installation Manual is the information on the design and technical

characteristics of the triboelectric guard alarm “Tribo-M” meant for perimeter areas (hereinafter referred to as

guard alarm) as well as the information on its installation and use.

General information

1.1 Purpose

Triboelectric single-position passive and unmasked guard alarm “Tribo-M” with surface detection zone

is designed for extended perimeter areas and is used as a stationary unit.

The guard alarm for perimeter fences mean to generate alarm signals after the local

deformation/vibration of the fence and the sensitive element fastened to it in the case of an unauthorized

penetration by climbing over the fence, without any facility, and as a result - deformation/vibration of the fence

and the sensitive element over its fasteners.

The guard alarm ensures the monitoring of the sensitive element integrity (the element of tribo electric

effect), the connecting element being checked as well. On their damage (short-circuit or broken element) the

guard alarm generates an alarm signal on the fault.

Summary of Contents for TRIBO-M





















































Search results

Summary of Contents for TRIBO-M

Reviews:

Related manuals for TRIBO-M

Brands by name

Popular brands

FORTEZA TRIBO-M, Operation & Installation Manual

Search results

Summary of Contents for TRIBO-M

Reviews:

Related manuals for TRIBO-M

Brands by name

Popular brands