FORTEZA TRIBO-M Operation & Installation Manual Download

Page: 49 / 52

JSC FORTEZA FORTEZA TRIBO-M

Please visit our internet sites:

www.forteza.com

www.forteza.eu

Page 49

System parameters

To set the parameters of the Forteza “Tribo-m”, choose

System

in the

Configuration

chapter.

To set the date and time press the „>” button for the

Set date

and

Set time

features. After typing in the wished

date and time press

Apply

and check, if the correct date and time appear in the respective windows. The correct

date and time is substantial for the operation of the system log.

Note:

The date and time settings disappear, when the power supply is interrupted. Always set the date

and time repeatedly, if the power supply of the system was switched off.

The “Software version” indicates, when the running version of the software was installed, also the

characteristics of this version. The manufacturer develops the software constantly. The development is carried

out in a way that the latest version of the software is always compatible with every older versions of the Forteza

“Tribo-M”. Thus you can always download the latest version of the software.It will always be compatible with

your Forteza “Tribo-m”.

Summary of Contents for TRIBO-M





















































Search results

Summary of Contents for TRIBO-M

Reviews:

Related manuals for TRIBO-M

Brands by name

Popular brands

FORTEZA TRIBO-M, Operation & Installation Manual

Search results

Summary of Contents for TRIBO-M

Reviews:

Related manuals for TRIBO-M

Brands by name

Popular brands