FORTEZA TRIBO-M Operation & Installation Manual Download

Page: 48 / 52

JSC FORTEZA FORTEZA TRIBO-M

Please visit our internet sites:

www.forteza.com

www.forteza.eu

Page 48

Check of output relays

To check the operation of the relay-contacts open

Tests

menu.

To check the operation of the relay-contacts choose

Modify

in the “Relay check” field. Then switch to

test-mode in the

Control (

1. relay, 2. relay, 3. relay, All relays). Choose the status of the relays to be checked

(connect, disconnect), then press

Apply.

Check the connecting/disconnecting of the relays with a control set.

Note:

After checking the operation of the relays do not forget to switch off the test-mode (

Disabled

the

Control

field) than confirm it by pressing

Apply

. Otherwise the test-mode will be switched on and the

status of the relays will not match the actual status of the channel (the relay will stay opened, thus provoking an

alarm, even if no alarm signal coming from the detector/detectors).

Leds check

– don’t use at the moment.

Summary of Contents for TRIBO-M





















































Search results

Summary of Contents for TRIBO-M

Reviews:

Related manuals for TRIBO-M

Brands by name

Popular brands

FORTEZA TRIBO-M, Operation & Installation Manual

Search results

Summary of Contents for TRIBO-M

Reviews:

Related manuals for TRIBO-M

Brands by name

Popular brands