formlabs Form Cure L Installation And Usage Instructions Download Page 33

Page: 33 / 40

Troubleshooting |

Error

Cause

Solution

Temperature fault occurred.

The Form Cure L thermistor

reported an error.

•

Disconnect and reconnect the power.

•

Disconnect the power. Remove

the Form Cure L top shell and

check that the thermistor wiring is

secure. Contact

Formlabs Support

or a

certified service provider

for

more information.

The LED brightness

encountered an error.

The Form Cure L

encountered an error while

setting the brightness of

the LEDs.

•

Disconnect and reconnect the power.

•

Disconnect the power. Unscrew

each of the three LED modules

(accessible from within the post-cure

chamber) and check that their wiring

is secure. Contact

Formlabs Support

or a

certified service provider

for

more information.

The set limit failed.

The Form Cure L

encountered an error

while setting the current

temperature limit.

•

Disconnect and reconnect the power.

•

Disconnect the power. Unscrew

each of the three LED modules

(accessible from within the post-cure

chamber) and check that their wiring

is secure. Contact

Formlabs Support

or a

certified service provider

for

more information.

The set duty cycle failed.

The Form Cure L

encountered an error while

setting the brightness of

the LEDs.

•

Disconnect and reconnect the power.

•

Disconnect the power. Unscrew

each of the three LED modules

(accessible from within the post-cure

chamber) and check that their wiring

is secure. Contact

Formlabs Support

or a

certified service provider

for

more information.

The door is open.

Please close.

The door is open while the

Form Cure L is trying to begin

a cycle.

Close the Form Cure L door.

The device failed to reach

the required temperature.

The Form Cure L did not

reach its target temperature

within 30 minutes.

Disconnect the power. Remove the

Form Cure L top shell and check that

the thermistor and heater module wiring

is secure. Contact

Formlabs Support

or a

certified service provider

for

more information.

An error occurred with the

device’s turntable.

The turntable was unable

to move properly due to an

issue with the motor driver or

the motor command.

Disconnect and reconnect the power.

An unknown error occurred

Other/unspecified cause

Disconnect and reconnect the power.

Summary of Contents for Form Cure L









































Search results

Summary of Contents for Form Cure L

Reviews:

Brands by name

Popular brands

formlabs Form Cure L, Installation And Usage Instructions

Search results

Summary of Contents for Form Cure L

Reviews:

Brands by name

Popular brands