manualshive.com logo in svg

Formax FD 150, Operator'S Manual

Share
Download
Formax FD 150 Operator'S Manual Download Page 48

Operating Manual

 

44

 

 

1/97

 

 

trouble 

cause 

remedy 

4. Misplaced 

imprint. 

Imprint position is not set 
correctly. 

Select a different 
MEMORY IMPRINT 
POSITION or re-adjust 
the imprint position. 
Refer to 

Sections 6.4 & 

6.6

. 

SADDLE HOLDER and 
INK ROLL CARRIAGE are 
not located correctly. 

Re-adjust imprint 
position. Refer to 

Section 6.6

. 

EXECUTIVE KEY was 
turned too quickly to index 
SADDLE HOLDER. 

Turn the EXECUTIVE 
KEY to the 

UNLOCKED

 

position, then 

slowly

 turn 

it to the 

LOCKED

 

position. 

5.  Partial ink on 

document. 

INK ROLL is not 
positioned over the 
IMPRINT SADDLE 
correctly. 

Open the COVER and 
align the INK ROLL 
CARRIAGE directly 
above the SADDLE 
HOLDER. 

6. Light imprint. 

IMPRINT SADDLES are  
not being inked. 
 

Turn the INK 
ADJUSTMENT KNOB 
clockwise to darken 
imprint. 

INK ROLL is out of ink. 

Install a new INK ROLL. 
To order a new INK 
ROLL, call your 

Formax Dealer

. 

IMPRINT SADDLES are 
worn. 

Install new IMPRINT 
SADDLES. To order a 
new pair, call your 

Formax Dealer

. 

 

Summary of Contents for FD 150

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands