Formax FD 150 Operator'S Manual Download Page 46

Page: 46 / 48

Operating Manual

1/97

9. Push the COTTER PIN until the AXLE is secured

between the two CLIPS on the COTTER PIN.

8.1.4 Document

Jam

If the

150

stops feeding, there may be one or more

documents jammed inside the machine. To clear a jam,
follow this procedure:

1. Unplug the POWER CORD.
2. Turn the EXECUTIVE KEY to the

UNLOCKED

position.

3. Open the COVER.
4. Remove the PRESSURE TIRE SHAFT by pushing the

spring-loaded end of the PRESSURE TIRE SHAFT
toward the hole opposite the operator’s side. Pull the
other end toward you and out of the machine.

5. Pull any jammed documents out of the

150

6. Push the spring loaded end of the PRESSURE TIRE

SHAFT into hole opposite the operator side.

Mate

the other end of the PRESSURE TIRE SHAFT

into the d-hole on the operator’s side and release.

8.2 Troubleshooting

Chart

The following Troubleshooting Chart helps you identify
and correct malfunctions. To use the Troubleshooting
Chart:

1. Locate the malfunctions in the

trouble

column.

2. Read across to the

cause

column.

3. Follow the instructions given in the

remedy

column.

Summary of Contents for FD 150

















































Search results

Summary of Contents for FD 150

Reviews:

Brands by name

Popular brands

Formax FD 150, Operator'S Manual

Search results

Summary of Contents for FD 150

Reviews:

Brands by name

Popular brands