background image

02

Des.      \     Model

22S

Power Supply

-

1~,

 120

V,

 6

0Hz

Cutting Capacity_

(80gsm paper)

m

mm
mm
mm
mm

K

45

PP

Max.Cutting Width 

430 

430 

PP

51 

Max.Cutting Length
Min.Cutting Lenth
Main Motor Power

0.4 (1/2HP)

Dimensions(LxWxH)

 700x625x1200

Weight 

9

2

3951

1~,120V,60Hz

45 (450 sheets)

430 

430 

51 

0.4 (1/2HP)

 700x625x1200

90

3952S

1~,230V,50Hz

45 (450 sheets)

430 

430 

51 

0.4 (1/2HP)

 700x625x1200

92

3951S

1~,120V,60Hz

45 (450 sheets)

430 

430 

51 

0.4 (1/2HP)

 700x625x1200

92

The back-gauge crank, clamp hand wheel with screws and some related tools are separately and properly packed in a 

box with the machine. Please install these items right away.

Installation of the machine:

The top part of the machine and the stand must be connected as follows:

1. Assemble the stand in the way that the 4 foundations match the colors marked on the stand, and secure each 

    connected part with hexagonal screws.

2. Correctly place and install the machine on the stand with care , and tighten the 4 hexagonal nuts to secure the stand 

    and machine.

1. Push the back-gauge crank slightly toward the machine and turn it counterclockwise in order to load the paper pile 
    on the deck.

2. Turn the clamp hand wheel clockwise to clamp the paper pile and close the safety guard.
3. Push the 2 enable switches simultaneously and hold them until the cutting cycle is complete. 
4. The optical cutting line will project the right cutting position on the paper pile.

Operation Description

Specification:

To 

prevent 

the 

back gauge

 device moving forward and backward while cutting

,

 

p

ull the back-gauge crank toward to the operator to make it idle.

Note :

Note :

Summary of Contents for Cut-True 22S














Reviews: