background image

48

48

3.9 R

églage du m

ode « E-heat

er »

Activation du mode « E-heater » (fonction de chauffage électrique auxiliaire) : En

mode « Heat », le mode « E-heater » peut être activé pour améliorer l’efficacité.

Quand le mode « Heat » est activé à l’aide du panneau de commande mural ou de

la télécommande sans fil, ce mode s’activera automatiquement.

En mode « Heat », appuyez sur le bouton « Function » pour accéder aux paramè-

tres de réglage du mode « E-heater ». Appuyez sur le bouton « Enter/Cancel »

pour désactiver ce mode.

Quand la fonction « E-heater » n’est pas activée, appuyez sur le bouton « Function

»pour accéder aux paramètres de réglage du mode « E-heater ». 

Appuyez sur le

bouton « Enter/Cancel » pour désactiver ce mode.

La figure 12 illustre comment régler le mode « E-heater ».

10

10

En mode « Heat », le

mode « E-heater »

(fonction de chauffage

électrique auxiliaire)

sera activé 

automatiquement.

Appuyez sur le bouton «

Function » pour accéder

au mode « E-heater ».

Appuyez sur le bouton «

Function » pour accéder

au mode « E-heater »

(fonction de chauffage

électrique auxiliaire).

Appuyez sur le bouton «

Enter/Cancel » pour acti-

ver le mode « E-heater ».

Appuyez sur le bouton «

Enter/Cancel » pour

désactiver le mode 

« E-heater ».

3.9 E-heater Setting

E-heater (auxiliary electric heating function): When running in the Heat mode,

the E-heater can be turned on to improve efficiency.

When the wired remote control or the remote control is set in the Heat mode,

this function will turn on automatically.

When running in the Heat mode, press “Function” to enter the E-heater setting

interface. Press “Enter/Cancel” to cancel this function.

If the E-heater function is not activated, press “Function” to enter the E-heater

setting interface. Press “Enter/Cancel” to turn it on.

How to set this function is shown in Fig.12

10

10

Auxilliary electric hea-

ting function is automati-

cally on in Heating

mode

Press (Function) button

into this function

Press “Function” until E-

heater 

Press (Enter/Cancel)

button to turn off this

function

Press (Enter/Cancel)

button to turn on this

function

Summary of Contents for E23 Series




























































Reviews: