Ford 2011 Edge Page 109 Owner'S Manual Download | Manualshive

Page: 109 / 403

background image

Do not use the HomeLink

威

Wireless Control System with any garage

door opener that lacks safety stop and reverse features as required by
U.S. federal safety standards (this includes any garage door opener
model manufactured before April 1, 1982). A garage door which cannot
detect an object, signaling the door to stop and reverse, does not meet
current U.S. federal safety standards. For more information, contact
HomeLink

威

at:

www.homelink.com

or

1–800–355–3515.

Retain the original transmitter for use in other vehicles as well as for
future programming procedures (i.e. new HomeLink

威

equipped vehicle

purchase). It is also suggested that upon the sale of the vehicle, the
programmed Homelink

威

buttons be erased for security purposes, refer to

Programming

in this section.

Programming

Do not program HomeLink

威

with the vehicle parked in the garage.

Note:

Your vehicle may require the ignition switch to be turned to the

accessory position for programming and/or operation of the HomeLink

威

.

It is also recommended that a new battery be placed in the hand-held
transmitter of the device being programmed to HomeLink

威

for quicker

training and accurate transmission of the radio-frequency signal.

1. Position the end of your
hand-held transmitter 1–3 inches
(2–8 cm) away from the HomeLink

威

button you wish to program (located
on your visor) while keeping the
indicator light in view.

2. Simultaneously press and hold
both the chosen HomeLink

威

and

hand-held transmitter buttons until the HomeLink

威

indicator light

changes from a slow to a rapidly blinking light. Now you may release
both the HomeLink

威

and hand-held transmitter buttons.

Note:

Some entry gates and garage door openers may require you to

replace Step 2 with procedures noted in the

Gate Operator and

Canadian Programming

in this section for Canadian residents.

3. Firmly

press and hold for five seconds and release

the

programmed HomeLink

威

button up to two separate times to activate the

door. If the door does not activate, press and hold the just-trained
HomeLink

威

button and observe the indicator light.

Driver Controls

109

2011 Edge

(edg)

Owners Guide, 1st Printing
USA

(fus)

«
...
107
108
109
110
111
...
»

Summary of Contents for 2011 Edge




















































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Edge

Brand: B-Speech Pages: 24

Brand: Caltrend Pages: 2

Brand: Audiovox Pages: 1

EGR-3PVE-COLOUR

Brand: EGR Pages: 28

Carpower CAP-20

Brand: Monacor Pages: 2

Brand: GMC Pages: 430

Brand: iArmor Pages: 6

Brand: SNIPER Pages: 2

PRIME DESIGN HXR-269-E-UM3-80

Brand: Safe Fleet Pages: 12

Brand: travall Pages: 4

CERTA CTCVINCVR14A

Brand: Kogan Pages: 4

2000 Accord Sedan

Brand: Honda Pages: 320

Brand: Scosche Pages: 8

Brand: Roadefend Pages: 15

Brand: Yakima Pages: 10

Platinum Pro Plug-in

Brand: Haltech Pages: 20

Brand: Vauxhall Pages: 215

Brand: Intellitronix Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands