manualshive.com logo in svg

Ford 2010 MKX, Owner'S Manual

The Ford 2010 MKX product is accompanied by a comprehensive Quick Reference Manual that provides users with invaluable information and instructions. This essential manual is available for download, absolutely free, from our website. Enhance your MKX experience by accessing this user-friendly manual at manualshive.com.

Share
Download
background image

•

If required, add engine oil to the
engine. Refer to

Adding engine

oil

in this chapter.

•

Do not overfill the engine
with oil. Oil levels above this
mark may cause engine
damage.

If the engine is

overfilled, some oil must be
removed from the engine by an
authorized dealer.

7. Put the dipstick back in and
ensure it is fully seated.

Adding engine oil

1. Check the engine oil. For
instructions, refer to

Checking the engine oil

in this chapter.

2. If the engine oil level is not within the normal operating range, add
only certified engine oil of the recommended viscosity. Remove the
engine oil filler cap and use a funnel to pour the engine oil into the
opening.

3. Recheck the engine oil level. Make sure the oil level is not above the
normal operating range on the engine oil level dipstick.

4. Install the dipstick and ensure it is fully seated.

5. Fully install the engine oil filler cap by turning the filler cap clockwise
until it stops.

To avoid possible oil loss, DO NOT operate the vehicle with the
engine oil level dipstick and/or the engine oil filler cap removed.

Maintenance and Specifications

271

2010 MKX

(mkx)

Owners Guide, 3rd Printing
USA

(fus)

Summary of Contents for 2010 MKX


























































































































































































































































































































Reviews:

No comments

Related manuals for 2010 MKX

Federal Signal Corporation 7000 Assembly Instructions Manual preview
7000
Brand: Federal Signal Corporation Pages: 13
iDataLink maestro Rr Install Manual preview
maestro Rr
Brand: iDataLink Pages: 106
Vauxhall Cascada Quick Reference Manual preview
Cascada
Brand: Vauxhall Pages: 2
Yakima K618 Instructions Manual preview
K618
Brand: Yakima Pages: 11
FABBRI PORTATUTTO 17405400 Assembly Instructions preview
17405400
Brand: FABBRI PORTATUTTO Pages: 2
FVC Sprinter Bed System Adventure Wagon Kit Installation Manual preview
Sprinter Bed System Adventure Wagon Kit
Brand: FVC Pages: 8
Metra Electronics 99-3103 Installation Instructions preview
99-3103
Brand: Metra Electronics Pages: 2
FORM FIT HDW 1779 Installation Instructions preview
HDW 1779
Brand: FORM FIT Pages: 2
Subaru 2016 Outback Owner'S Manual preview
2016 Outback
Brand: Subaru Pages: 99
Fiat 500 L 2019 User Manual preview
500 L 2019
Brand: Fiat Pages: 172
Honda HondaLink Quick Start Manual preview
HondaLink
Brand: Honda Pages: 6
Parkeon StradaPAL Installation Manual preview
StradaPAL
Brand: Parkeon Pages: 43
VDO RUDDER ANGLE INDICATOR Installation Instructions Manual preview
RUDDER ANGLE INDICATOR
Brand: VDO Pages: 8
Chevrolet 1996 Cavalier Owner'S Manual preview
1996 Cavalier
Brand: Chevrolet Pages: 372
Fab Fours H4550 Installation Instructions Manual preview
H4550
Brand: Fab Fours Pages: 13
Skoda OCTAVIA - TECHNICAL CHANGES 11-2009 Owner'S Manual Supplement preview
OCTAVIA - TECHNICAL CHANGES 11-2009
Brand: Skoda Pages: 16
Subaru 2003 Baja Owner'S Manual preview
2003 Baja
Brand: Subaru Pages: 32
Hummer HX-T Owner'S Manual preview
HX-T
Brand: Hummer Pages: 31

Brands by name

Popular brands

Load more brands