Ford 2009 Taurus X Owner'S Manual Download Page 297

Page: 297 / 336

5. Locate and carefully remove the
engine oil level dipstick.

6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again.

•

If the oil level is

within this

range,

the oil level is acceptable.

DO NOT ADD OIL.

•

If the oil level is

below this

mark,

engine

oil must be added

to raise the level within the
normal operating range.

•

If required, add engine oil to the
engine. Refer to

Adding engine

oil

in this chapter.

2009 Taurus

(500)

Owners Guide, 1st Printing
USA

(fus)

Maintenance and Specifications

297

Summary of Contents for 2009 Taurus X

















































































































































































































































































































































Search results

Summary of Contents for 2009 Taurus X

Reviews:

Related manuals for 2009 Taurus X

Brands by name

Popular brands

Ford 2009 Taurus X, Owner'S Manual

Search results

Summary of Contents for 2009 Taurus X

Reviews:

Related manuals for 2009 Taurus X

Brands by name

Popular brands