Ford 2009 Taurus X Owner'S Manual Download Page 178

Page: 178 / 336

WARNING:

Several air bag system components get hot after

inflation. Do not touch them after inflation.

WARNING:

If the side

airbag has deployed,

the

airbag will not function again.
The side airbag system
(including the seat) must be
inspected and serviced by an
authorized dealer.

If the airbag

is not replaced, the unrepaired
area will increase the risk of injury
in a collision.

Safety Canopy

姞

system

WARNING:

Do not place

objects or mount equipment

on or near the headliner at the
siderail that may come into
contact with a deploying Safety
Canopy

威

. Failure to follow these

instructions may increase the risk
of personal injury in the event of a
collision.

WARNING:

Do not lean your head on the door. The Safety

Canopy

威

could injure you as it deploys from the headliner.

WARNING:

Do not attempt to service, repair, or modify the

Safety Canopy

威

system, its fuses, the A, B, or C pillar trim, or

the headliner on a vehicle containing a Safety Canopy

威

. See your

authorized dealer.

2009 Taurus

(500)

Owners Guide, 1st Printing
USA

(fus)

Seating and Safety Restraints

178

Summary of Contents for 2009 Taurus X

















































































































































































































































































































































Search results

Summary of Contents for 2009 Taurus X

Reviews:

Related manuals for 2009 Taurus X

Brands by name

Popular brands

Ford 2009 Taurus X, Owner'S Manual

Search results

Summary of Contents for 2009 Taurus X

Reviews:

Related manuals for 2009 Taurus X

Brands by name

Popular brands