Ford 2009 Taurus X Owner'S Manual Download Page 89

Page: 89 / 336

3. Remove the outboard rubber boot
from the lamp assembly by pulling
rearward.

4. Remove the bulb socket by
turning it counterclockwise and
pulling it straight out.

WARNING:

Handle a halogen headlamp bulb carefully and keep

out of children’s reach. Grasp the bulb only by its plastic base

and do not touch the glass. The oil from your hand could cause the
bulb to break the next time the headlamps are operated.

Install the new bulb(s) in reverse order.

Replacing headlamp (high beam) bulbs

1. Make sure the headlamp switch is in the off position, then open the
hood.

2. Reach in behind the headlamp assembly to access the bulb sockets
and connectors.

3. Remove the inboard rubber boot
from the lamp assembly by pulling
rearward.

4. Remove the bulb socket by
turning it counterclockwise and
pulling it straight out.

WARNING:

Handle a halogen headlamp bulb carefully and keep

out of children’s reach. Grasp the bulb only by its plastic base

and do not touch the glass. The oil from your hand could cause the
bulb to break the next time the headlamps are operated.

Install the new bulb(s) in reverse order.

2009 Taurus

(500)

Owners Guide, 1st Printing
USA

(fus)

Lights

Summary of Contents for 2009 Taurus X

















































































































































































































































































































































Search results

Summary of Contents for 2009 Taurus X

Reviews:

Related manuals for 2009 Taurus X

Brands by name

Popular brands

Ford 2009 Taurus X, Owner'S Manual

Search results

Summary of Contents for 2009 Taurus X

Reviews:

Related manuals for 2009 Taurus X

Brands by name

Popular brands