Ford 2000 Ranger Workshop Manual Download

Page: 57 / 62

Yes

GO to

E24

GO to

E23

E23

CHECK THE LH SIDE WHEEL END FOR LEAKS

Reconnect the RH wheel end vacuum line connector.

Disconnect the LH wheel end vacuum line connector.

NOTE:

This step may require rapid pumping for up to 10 seconds.

Connect a hand vacuum pump to the LH wheel end vacuum line connector and try to pull a vacuum to 15
in/Hg.

Does the vacuum drop exceed 0.5 in/Hg in 30 seconds?

Yes

GO to

E24

VERIFY all vacuum line connections are OK. TEST the system for normal operation. If a vacuum leak is still
present, REPLACE the PVH solenoid vacuum line. TEST the system for normal operation.

E24

CHECK THE CHASSIS VACUUM LINE FOR LEAKS

Carefully disconnect the chassis vacuum line from the steel vacuum line.

NOTE:

This step may require rapid pumping for up to 10 seconds.

Connect a hand vacuum pump to the steel vacuum line and try to pull a vacuum to 15 in/Hg.

Does the vacuum drop exceed 0.5 in/Hg in 30 seconds?

Yes

Page 57 of 62

2000 Ranger Workshop Manual

1/18/2012

http://www.fordtechservice.dealerconnection.com/pubs/content/~WSYL/~MUS~LEN/21/...

Summary of Contents for 2000 Ranger































































Search results

Summary of Contents for 2000 Ranger

Reviews:

Related manuals for 2000 Ranger

Brands by name

Popular brands

Ford 2000 Ranger, Workshop Manual

Search results

Summary of Contents for 2000 Ranger

Reviews:

Related manuals for 2000 Ranger

Brands by name

Popular brands