Fondital minorca kr Installation, Use And Maintenance Manual Download Page 19 | Manualshive

Page: 19 / 64

background image

19

Technical features and dimensions

2.1.3

Operating features

•  CH electronic flame modulation with timer-controlled rising ramp (30 minutes, adjustable).
•  DHW electronic flame modulation (mdoels KC and KR/KRB with optional water heater).
•  DHW priority function (model KC and models KR/KRB with optional water heater)
•  Flow freeze protection function: ON 5°C; OFF 30°C or after 15 minutes of operation if CH temperature > 5 °C.
•  DHW freeze protection function: ON 5°C; OFF 30°C or after 15 minutes of operation if CH temperature > 5 °C.
•  Water heater anti-freeze function (KR with optional external water heater with NTC probe): ON 5°C; OFF 10 °C or after 15 minutes of

operation if water heater temperature > 5 °C.

•  Timer-controlled flue cleaning function: 15 minutes.
•  Anti-legionella function (models KR/KRB with optional water heater).
•  CH Maximum heat input parameter adjustment.
•  Ignition heat input adjustment parameter.
•  Possibility to select the heating range: standard or reduced.
•  Ignition flame propagation function.
•  CH thermostat timer: 30 minutes (adjustable).
•  Heating pump post-circulation function in CH, freeze protection and flue cleaning modes: 30 seconds (adjustable).
•  DHW post-circulation function (KC and KR/KRB with optional water heater): 30 seconds.
•  Post-circulation function for heating temperature > 78 °C: 30 seconds.
•  Post-ventilation function after working: 10 seconds.
•  Post-ventilation function for CH temperature >95 °C.
•  Circulation pump and deviating valve anti shut-down function: 10 seconds of operation after 24 hours of inactivity (adjustable).
•  Anti-water hammer function: can be set from 0 to 10 seconds through parameter P15.
•  Ready for connection to an (optional) ambient thermostat.
•  Ready for operation with an external probe (optional, supplied by the manufacturer).
•  Ready for operation with an ambient probe (optional, supplied by the manufacturer).
•  Ready for operation with an OpenTherm remote control (optional, supplied by the manufacturer).

«
...
17
18
19
20
21
...
»

Summary of Contents for minorca kr

































































Reviews:

No comments

Related manuals for minorca kr

Brand: Demir Dokum Pages: 80

Brand: Laars Pages: 36

Vitodens 100 Series

Brand: Viessmann Pages: 112

Brand: tado° Pages: 20

Brand: Ideal Boilers Pages: 8

Brand: Beretta Pages: 108

Brand: Slant/Fin Pages: 4

Brand: NTI Pages: 8

RemaSol200SE-2S

Brand: REMEHA Pages: 80

Brand: LAMBORGHINI Pages: 48

Brand: Teba therm Pages: 21

Brand: Drazice Pages: 23

Brand: Biodom Pages: 61

Brand: Atag Pages: 10

Brand: Atag Pages: 64

Brand: Atag Pages: 64

Brand: Aerco Pages: 154

Hydra Smart RT-199

Brand: HTP Pages: 73

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands