background image

Operation Manual RTM MP Plus 

 

 

06.03.2019

 

 

3

 

Certifications and Compliancy 

This equipment has been tested and found to comply with following rules: 

 

ETSI Radio Certification

 

Magnitude of Test (Coverage)  Article 3.2 of Directive 1999/5/EC (R&TTE 

Directive) 

Certification 

ETSI EN 300 440-2 V1.5.1 (2009-03) 
ETSI EN 300 440-1 V1.3.1 (2009-03) 

ETSI EMC Certification 

Magnitude of Test (Coverage)  ECM-Test according to 98/37/EC and 

2004/108/EC harmonized 

Emission and Immunity Test 

ETSI EN 489-3  
EN 61326-1 

FCC Certification 

 

Magnitude of Test 

Class A digital device, pursuant to Part 15 of the 
FCC Rules  

Certification 

FCC Registration #: 0020311882 

 

 

Note 

This equipment has been tested and found to comply with the limits for a Class A 

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference when the equipment is 
operated in a commercial environment. This equipment generates, uses, and can 
radiate radio frequency energy and, if not installed and used in accordance with the 

instruction manual, may cause harmful interference to radio communications. 
Operation of this equipment in a residential area is likely to cause harmful 
interference in which case the user will be required to correct the interference at his 
own expense. 

 

 

 

Summary of Contents for RTM MP Plus EMGZ443MP.R

























Reviews: