background image

www.fmiproducts.com

119303-01G

7

AIR FOR COMBUSTION AND VENTILATION

Continued

4.  Compare the maximum Btu/Hr the space 

can support with the actual amount of Btu/

Hr used.

 

 _______ Btu/Hr (maximum the space can 

support)

 

 _______ Btu/Hr (actual amount of Btu/Hr 

used)

 

Example:

  63,360  Btu/Hr  (maximum  the 

space can support) 

 

 

79,000 Btu/Hr (actual amount of 

Btu/Hr used)

The space in the above example is a confined 

space because the actual Btu/Hr used is more 

than the maximum Btu/Hr the space can sup-

port. You must provide additional fresh air. Your 

options are as follows:

A.  Rework worksheet, adding the space of an 

adjoining room. If the extra space provides an 

unconfined space, remove door to adjoining 

room or add ventilation grills between rooms. 

See 

Ventilation Air  From  Inside  Building

page 8

.

B.  Vent room directly to the outdoors. See 

Ventilation Air From Outdoors

page 8.

C.  Install a lower Btu/Hr fireplace, if lower Btu/

Hr size makes room unconfined. 

If the actual Btu/Hr used is less than the 

maximum Btu/Hr the space can support,

 

the 

space is an unconfined space. You will need 

no additional fresh air ventilation.

 WARNING: If the area in which 

the heater may be operated does 

not meet the required volume for 

indoor combustion air, combus

-

tion and ventilation air shall be 

provided by one of the methods 

described in the 

National Fuel 

Gas Code, ANSI Z223.1/NFPA 54, 

the

 International Fuel Gas Code,

 

or applicable local codes.

  40,000
  39,000
  79,000

DETERMINING FRESH-AIR FLOW 

FOR HEATER LOCATION

Determining if You Have a Confined or 

Unconfined Space

Use this work sheet to determine if you have 

a confined or unconfined space.

Space:

 Includes the room in which you will 

install heater plus any adjoining rooms with 

doorless passageways or ventilation grills 

between the rooms.

1.  Determine the volume of the space (length 

x width x height).

 

Length x Width x Height =__________cu. ft. 

(volume of space)

 

Example: 

Space size 22 ft. (length) x 18 ft. 

(width) x 8 ft. (ceiling height) = 3168 cu. ft. 

(volume of space)

 

If additional ventilation to adjoining room 

is supplied with grills or openings, add the 

volume of these rooms to the total volume 

of the space. 

2.  Multiply the space volume by 20 to deter-

mine the maximum Btu/Hr the space can 

support.

 

 ________ (volume of space) x 20 = (Maxi-

mum Btu/Hr the space can support)

 

Example:

 3168 cu. ft. (volume of space) x 20 

= 63,360 (maximum Btu/Hr the space can 

support)

3.  Add the Btu/Hr of all fuel burning appliances 

in the space.

 

Vent-free fireplace 

 __________ Btu/Hr

 

Gas water heater* 

 __________ Btu/Hr

 

Gas furnace 

 __________ Btu/Hr

 

Vented gas heater 

 __________ Btu/Hr

 

Gas fireplace logs 

 __________ Btu/Hr

 

Other gas appl __________ Btu/Hr

 Total 

= _________ Btu/Hr

 

* Do not include direct-vent gas appliances. 

Direct-vent draws combustion air from the 

outdoors and vents to the outdoors.

 

Example:

 

Gas water heater 

 __________ Btu/Hr

 

Vent-free fireplace 

+

 _________ Btu/Hr

 Total 

= _________ Btu/Hr

Summary of Contents for VSGF28NTF

































Reviews: