background image

www.fmiproducts.com

112301-01E

9

FIREPLACE 

INSTALLATION

Continued

This unit has been tested for installation at high 

altitude. Higher altitudes affect the atmospheric 

pressure and heat valve of gaseous fuels. When 

installing  this  unit  at  high  altitudes,  the  rated 

input will be lower than at sea level. The lowered 

oxygen  content  in  the  air  and  the  lowered  gas 

density  require  installation  of  a  different  size 

orifice in order to achieve clean combustion of 

the unit. Consult the unit data plate for the proper 

high-altitude orifice size. Fill out the information 

sticker attached to the unit when field converting. 

See 

Specifications,

 page 14, when derating. 

Figure 12 - Millivolt Control Valve

Figure 13 - Electronic Control Valve

ON/OFF 

Knob

Pilot 

Adjustment 

Cap

Pilot Gas Line

Do Not Kink

Inlet 

Pressure

Outlet 

Pressure

To Main 

Burner

To Pilot 

Burner

E

A

From 

Gas 

Supply

To 

Main 

Burner

Inlet 

Pressure

Outlet 

Pressure

A manual shutoff valve has been included in the 

appliance’s gas supply system. You may consider 

installing an extra gas shutoff valve outside the ap-

pliance’s enclosure (check with local codes) where 

it can be accessed more conveniently with a key 

through a wall as shown in Figure 14.
Route  a  1/2"  NPT  gas  line  towards  appliance 

coming in from back of appliance. If installation 

permits, you may alternately route your incoming 

gas line from bottom of appliance toward either 

end. It is recommended to route gas pipe from back 

of fireplace if possible.

 CAUTION: Do not kink flex

-

ible gas line.

 CAUTION: Compounds used 

on threaded joints of gas piping 

shall be resistant to the action of 

Liquefied  Petroleum  (propane/

LP) and should be applied lightly 

to ensure excess sealant does 

not enter the gas line.

1.  Install a sediment trap between incoming gas 

line and gas control valve (see Figure 15). 

Sediment trap should extend down center of 

pipe. Refer to your local codes.

Key

Extension

Shutoff 

Valve

Figure 14 - Typical Exterior Wall Gas 

Shutoff Installation

GAS LINE HOOK-UP

 WARNING: Gas line hookup 

should  be  done  by  your  gas 

supplier  or  a  qualified  service 

person.

 WARNING: Before you pro-

ceed, make sure your gas supply 

is OFF.

Figure 15 - Sediment Trap

3" Min.

(76 mm)

Side W

all

Of Appliance

Incoming 1/2" Gas Line 

Permitted by Local Codes

Sediment 

Trap (Not 

Supplied)

Summary of Contents for (V)gl36cl(e)





















Reviews: