background image

www.fmiproducts.com

115603-01D

11

Secure 

Termination 

to Outer 

Pipe with 3 

Screws

RLT-12D

Stainless 

Inner Flue 

Pipe

Apply 

Waterproof 

Caulking

Storm 

Collar

Flashing

Underlap 

Shingles

Figure 26 - Terminations

Overlap 

Shingles (Top 

and Sides of 

Flashing Base)

VenTing inSTallaTion

Continued

CHASE INSTALLATIONS

Instructions  for  chase  installations  are 

included  with  the  chase  style  termination 

chosen. In a multiple chase installation, be 

sure to provide adequate distance between 

terminations to prevent smoke spillage from 

one termination to another. Terminations must 

be separated a minimum of 30" center to cen-

ter and stacked at a minimum vertical height 

difference of 18" (see Figure 27).
Note: If a decorative shroud is to be installed, 

contact the manufacturer for specifications.

FINISHING FIREPLACE

Combustible  materials,  such  as  wallboard, 

gypsum board, sheet rock, drywall, plywood, 

etc. may make direct contact with sides and 

top around the fireplace face. It is important 

that combustible materials do not overlap the 

face itself. Brick, glass, tile or other noncom-

bustible materials may overlap the front face 

provided they do not obstruct essential open-

ings like louvered slots or any other opening. 

When  overlapping  with  a  noncombustible 

facing  material,  use  only  noncombustible 

mortar or adhesive.

INSTALLING FIREPLACE FACING

Any noncombustible material may be used for 

facing (glass, tile, brick, etc.) as long as proper 

clearances  are  adhered  to  and  fireplace 

openings are not obstructed in any way (see 

Minimum Clearance to Combustibles, page 

4 and Figure 28).
Use only heat resistant, noncombustible mor-

tar or adhesive when securing facing material 

to front of fireplace. When placing facing at 

upper edge of effective opening of fireplace, 

provide “L” shaped piece of metal extending 

full width of opening (see Figure 28).
Secure with sheet metal screws at a distance 

high enough from edge so it doesn't interfere 

with operation of doors. This assures that fac-

ing material will not block openings.

24" Min.

24" Min.

18" 

Min.

Typ.

Figure 27 - Multiple Chase Installation

1" 

Space

Screen

Chase 

Top

“L” Shaped 

Metal 

Support

Noncombustible 

Facing Material

Noncombustible 

Facing Material

Do Not 

Block 

Opening

Figure 28 - Fireplace Facing (Your 

Fireplace May Vary from Illustration)

1" 

Noncombustible 

Spacer

Summary of Contents for (V)3612ST

















Reviews: