FMI MF42INV Owner'S Operation And Installation Manual Download

Page: 33 / 44

www.fmiproducts.com

125568-01B

POSSIBLE CAUSE

1. Control knob not fully

pressed in

2. Control knob not pressed in

long enough

3. Safety interlock system has

been triggered

4. Equipment shutoff valve not

fully open

5. Pilot flame not touching

thermocouple,  which  al-
lows thermocouple to cool,
causing  pilot  flame  to  go
out. This problem could be
caused  by  one  or  both  of
the following:

A) Low gas pressure
B) Dirty or partially clogged

ODS/pilot

6. Thermocouple connection

loose at control valve

7. Thermocouple damaged
8. Control valve damaged

1. Inlet gas pressure is too

low

2. Burner orifice(s) clogged

3. Thermopile leads discon-

nected or improperly con-
nected.

4. Remote selector in OFF

position

5. Wire disconnected from gas

control

1. Manifold pressure is too

low

2. Burner orifice(s) clogged

3. Mislocated crossover tube

1. Burner orifice is clogged or

damaged

2. Damaged burner
3. Gas regulator defective

REMEDY

1. Press in control knob fully

2. After ODS/pilot lights, keep

control knob pressed in 30
seconds

3. Wait one minute for safety

interlock system to reset.
Repeat ignition operation

4. Fully open equipment shut-

off valve

5. A) Contact local natural or

propane/LP gas company

B) Clean ODS/pilot (see

Cleaning and Maintenance

page 30) or replace ODS/
pilot assembly

6. Hand tighten until snug,

then tighten 1/4 turn more

7. Replace pilot assembly
8. Replace control valve

1. Contact local natural or

propane/LP gas company

2. C l e a n b u r n e r ( s ) ( s e e

Cleaning and Maintenance

page 30) or replace burner
orifice(s)

3. Reconnect leads see

wiring

diagram

, page 30

4. Put remote selector in ON

position

5. See

Wiring Diagram

, page

1. Contact local natural or

propane/LP gas company

2. C l e a n b u r n e r ( s ) ( s e e

Cleaning and Maintenance

page 30) or replace burner
orifice(s)

3. Contact qualified service per-

son

1. Clean burner (see

Cleaning

and Maintenance

, page 30)

or replace burner orifice

2. Replace damaged burner
3. Replace gas regulator

OBSERVED PROBLEM

ODS/pilot lights but flame
goes out when control knob
is released

One or both burners do not
light after ODS/pilot is lit

Delayed ignition of one or
both burners

Burner backfiring during
combustion

TROUBLESHOOTING

Continued

Summary of Contents for MF42INV













































Search results

Summary of Contents for MF42INV

Reviews:

Related manuals for MF42INV

Brands by name

Popular brands

FMI MF42INV, Owner'S Operation And Installation Manual

Search results

Summary of Contents for MF42INV

Reviews:

Related manuals for MF42INV

Brands by name

Popular brands