manualshive.com logo in svg

FLYGT 3126.290, Installation, Operation And Maintenance Manual, Page: 27 / 48

Share
Download
FLYGT 3126.290 Installation, Operation And Maintenance Manual Download Page 27

A specially Flygt designed starter is required for the operation of single phase pumps.
The connection of the motor cable to the starter is shown in the wiring diagram.
1. If thermal contacts are included in the pump installation, then connect the T1 and T2

control conductors to the monitoring equipment.

NOTICE:

Ex-approved products must always have the thermal contacts connected irrespective
of the ambient temperature.

2. Connect the mains leads (L1, L2, L3, and ground (earth)) to the starter equipment.

For information about the phase sequence and the color codes of the leads, see 

Cable charts

 (page 25).

Cable charts

Description

This topic contains general connection information. It also provides cable charts that show
connection alternatives for use with different cables and power supply.

WS000509D

L2

L3

L1

L1

L3

L2

T1 T2

Figure 6: Phase sequence

Connections

WS008530A

Figure 7: 6 leads

Installation

Flygt 3126.290 Installation, Operation, and Maintenance Manual

25

Summary of Contents for 3126.290

















































Reviews:

No comments