manualshive.com logo in svg

FLYGT 3126.290, Installation, Operation And Maintenance Manual

Share
Download
FLYGT 3126.290 Installation, Operation And Maintenance Manual Download Page 19

Installation

Install the pump

Before starting work, make sure that the safety instructions in the chapter 

Introduction and

Safety

 (page 3) have been read and understood.

DANGER: Electrical Hazard

Before starting work on the unit, make sure that the unit and the control panel are isolated
from the power supply and cannot be energized. This applies to the control circuit as well.

DANGER: Inhalation Hazard

Before entering the work area, make sure that the atmosphere contains sufficient oxygen
and no toxic gases.

Hazardous atmospheres

DANGER: Explosion/Fire Hazard

Special rules apply to installations in explosive or flammable atmospheres. Do not install
the product or any auxiliary equipment in an explosive zone unless it is rated explosion-
proof or intrinsically-safe. If the product is EN/ATEX-, MSHA- or FM-approved, then see
the specific EX information in the Safety chapter before taking any further actions.

WARNING: Explosion/Fire Hazard

Do not install CSA-approved products in locations that are classified as hazardous in the
National Electric Code(TM), ANSI/NFPA 70-2005.

General requirements

These requirements apply:

• Use the pump dimensional drawing in order to ensure proper installation.
• In T-installation, the pump must be equipped with cooling jacket.

Before installing the pump, do the following:

• Provide a suitable barrier around the work area, for example, a guard rail.
• Make sure that equipment is in place so that the unit cannot roll or fall over during the

installation process.

• Check the explosion risk before you weld or use electric hand tools.
• Check that the cable and cable entry have not been damaged during transport.
• Always remove all debris and waste material from the sump, inlet piping, and

discharge connection, before you install the pump.

NOTICE:

• Never force piping to make a connection with a pump.

Authority regulation

Vent the tank of a sewage station in accordance with local plumbing codes.

Fasteners

• Only use fasteners of the proper size and material.
• Replace all corroded fasteners.
• Make sure that all fasteners are properly tightened and that there are no missing

fasteners.

Installation

Flygt 3126.290 Installation, Operation, and Maintenance Manual

17

Summary of Contents for 3126.290

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands